用 Arduino 和 Yeelink 控制 LED 灯的开关

做法很简单,就是用 Arduino 通过物联网 Yeelink 来控制 LED 灯的开关。
基本参考官方教程做的 http://blog.yeelink.net/?p=94
http://blog.yeelink.net/?p=94 。我为了方便调整数字端口,只加了一行代码而已。注意,不要使用10,11,12,13数字端口,会有数据从这几个端口流入流出,导致控制失效。

开关可以在网页端控制,也可以在手机app控制。手机app下载地址:http://www.yeelink.net/product/mobile 也许下载链接失效了,我下载不了,不过我在其他应用商店下载到了,直接搜索 yeelink 应该就能找到。

我的成品图:
1765978458

这是终端链接:http://www.yeelink.net/devices/3414/

点开全文获取全部代码:


/*
Yeelink sensor client power switch example
*/

#include
#include
#include
#include

byte buff[2];

// for yeelink api
#define APIKEY "e825dbce4840这里换成你的API1e5a27e" // replace your yeelink api key here
#define DEVICEID 3这里换成你的设备号4 // replace your device ID
#define SENSORID 5这里换成你的端口号4 // replace your sensor ID

// assign a MAC address for the ethernet controller.
byte mac[] = { 0x00, 0x1D, 0x72, 0x82, 0x35, 0x9D};
// initialize the library instance:
EthernetClient client;
char server[] = "api.yeelink.net"; // name address for yeelink API

unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds
boolean lastConnected = false; // state of the connection last time through the main loop
const unsigned long postingInterval = 3*1000; // delay between 2 datapoints, 30s
String returnValue = "";
boolean ResponseBegin = false;
int PINNUM = 7;

void setup() {
pinMode(PINNUM, OUTPUT);

Wire.begin();
// start serial port:
Serial.begin(57600);
// start the Ethernet connection with DHCP:
if (Ethernet.begin(mac) == 0) {
Serial.println("Failed to configure Ethernet using DHCP");
for(;;)
;
}
else {
Serial.println("Ethernet configuration OK");
}
}

void loop() {
// if there's incoming data from the net connection.
// send it out the serial port. This is for debugging
// purposes only:

if (client.available()) {
char c = client.read();
// Serial.print(c);
if (c == '{')
ResponseBegin = true;
else if (c == '}')
ResponseBegin = false;

if (ResponseBegin)
returnValue += c;
}
if (returnValue.length() !=0 && (ResponseBegin == false))
{
Serial.println(returnValue);

if (returnValue.charAt(returnValue.length() - 1) == '1') {
Serial.println("turn on the LED");
digitalWrite(PINNUM, HIGH);

}
else if(returnValue.charAt(returnValue.length() - 1) == '0') {
Serial.println("turn off the LED");
digitalWrite(PINNUM, LOW);
}
returnValue = "";
}
// if there's no net connection, but there was one last time
// through the loop, then stop the client:
if (!client.connected() && lastConnected) {
Serial.println();
Serial.println("disconnecting.");
client.stop();
}

// if you're not connected, and ten seconds have passed since
// your last connection, then connect again and send data:
if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) {
// read sensor data, replace with your code
//int sensorReading = readLightSensor();
Serial.print("yeelink:");
//get data from server
getData();
}
// store the state of the connection for next time through
// the loop:
lastConnected = client.connected();
}

// this method makes a HTTP connection to the server and get data back
void getData(void) {
// if there's a successful connection:
if (client.connect(server, 80)) {
Serial.println("connecting...");
// send the HTTP GET request:

client.print("GET /v1.0/device/");
client.print(DEVICEID);
client.print("/sensor/");
client.print(SENSORID);
client.print("/datapoints");
client.println(" HTTP/1.1");
client.println("Host: api.yeelink.net");
client.print("Accept: *");
client.print("/");
client.println("*");
client.print("U-ApiKey: ");
client.println(APIKEY);
client.println("Content-Length: 0");
client.println("Connection: close");
client.println();
Serial.println("print get done.");

}
else {
// if you couldn't make a connection:
Serial.println("connection failed");
Serial.println();
Serial.println("disconnecting.");
client.stop();
}
// note the time that the connection was made or attempted:
lastConnectionTime = millis();
}


原创文章,转载请注明: 转载自TAHO

本文链接地址: 《用 Arduino 和 Yeelink 控制 LED 灯的开关》:http://taho.cc/11968

相关文章

发表评论

电子邮件地址不会被公开。 必填项已用*标注